My baja

[Subatron]

Hey guys! Been a long time reader of scoobytruck and just thought I’d show y’all some shots of my ride.

So here’s what I’ve got done...

Td05 16g
ESS intercooler
3”downpipe
Exhaust is completely Catless now
2” adf subframe spacer lift.
1”strut spacers
1.5” long travel coil overs
20mm hub spacers
2002 wrx rims
Primitive racing under armor.
USB outlets replaced cigarette lighters
2002 wrx front seats

[Subatron]

EE8CD7BD-C742-4E9A-9ED5-1DC319E5C59A.jpeg (3.1 MiB) Viewed 9827 times

52583EAD-4FBC-49C9-BE1A-B4EF1D6DBE71.jpeg (2.97 MiB) Viewed 9827 times

5B91EBE5-DC35-4893-8DB1-5F88A6547364.jpeg (3.57 MiB) Viewed 9827 times

[Subatron]

25EAA06C-8485-4438-8EF3-42B30B42A97D.jpeg (3.04 MiB) Viewed 9827 times

B10642B1-677B-4217-A07E-1ED00108E95F.jpeg (3.2 MiB) Viewed 9827 times

6285ABC2-8CCF-43D2-9208-BDBB60B5E4A5.jpeg (1013.31 KiB) Viewed 9827 times

[Subatron]

5E696299-0374-411A-A54A-6B62BEAA70F1.jpeg (2.16 MiB) Viewed 9827 times

ED60D41C-D836-4D31-B3AC-169C0ABB7CFC.jpeg (2.19 MiB) Viewed 9827 times

FF456FC0-8C94-4B39-ADFA-F766DC494A7B.jpeg (1.67 MiB) Viewed 9827 times

[Subatron]

94D17F5C-D05A-434F-824A-2B286BD31A73.jpeg (651.13 KiB) Viewed 9827 times

D4BF187A-8191-458A-9D7C-EB92FC0E52DE.jpeg (1.82 MiB) Viewed 9827 times

39805812-93F3-4F45-8A9D-8F1316104964.jpeg (2.03 MiB) Viewed 9827 times

[Subatron]

Also-

grimmspeed lwcp
Hybrid boost control setup

[Subatron]

11A6E72B-27E9-4D3A-BE52-4AA96283495C.jpeg (2.69 MiB) Viewed 9826 times

04EC4094-0F49-4955-9CB3-1A40D8420B87.jpeg (616.27 KiB) Viewed 9826 times

4907B2C7-E022-460F-BEA3-C098539923B5.jpeg (1.96 MiB) Viewed 9826 times

[oldpro]

Nice overall, but to me photo #2 seems to show you have a whole lot of front wheel toe-out. Did your do an alignment after this photo was taken?

[Subatron]

• there May be a bit of toe out but I had the wheel cranked to give it a meaner look. I am going to give her an alignment after I wrap her in Some general grabbers before winter

[Subatron]

also- I’m looking to shape my bumper in a similar fashion to the picture attached.

Do y’all have any suggestions on how I might go about this?

[Subatron]

D7D6FD81-3677-4139-B2CB-77331EC3A827.jpeg (83.1 KiB) Viewed 9807 times

also- I’m looking to shape my bumper in a similar fashion to the picture attached.

Do y’all have any suggestions on how I might go about this?

[kamesama980]

as for the bumper, depends on how close you want it to match... sawsall followed up with something to clean up the edges would get the job done but that bumper had different openings to start with too.

Nice overall, but to me photo #2 seems to show you have a whole lot of front wheel toe-out. Did your do an alignment after this photo was taken?

Keep in mind when the wheels are turned there's something called Ackerman angle... the wheels don't stay parallel due to the different radii circles they follow.